For all the talk of the XX Cassette, the XX Crankset is really where they're changing the gearing paradigm. Double chain ring cranks have made consistent if periodic appearances in the MTB world for years. The reasons for their appearance have always been the same -- lighter weight, better Q-factor, better chain line, faster shifting, and no chain suck. Ritchey was the last to push 2x9 gearing starting back in 1997, and that was an era of seven and eight-speed cassettes. With nine-speed making its way into mountain bikes, 2x9 made sense for places without steep terrain.XX isn't Tom's 2x9. For one, with XX you still get the super-wide range you'd otherwise get with 3x9. For another, unlike Ritchey, they're designing the entire system rather than making a few pieces, then hacking designs for the rest.XX cranks are optimized for the 2x10 system. The only given was using two rings and a through-axle spindle. They went to the drawing board to re-imagine the rest. Looking at it, you know the crank is different -- different in a more profound way than even XTR. Both chain rings are affixed on the inside of the crankarm. This helps keep the q-factor down as well as keeping the chainline narrow, at 49.5mm. The outer ring as a 120mm bolt circle diameter while the inner has a 80mm bcd. These numbers seem odd, except that the outer was designed to work with 39, 42, and 45 tooth chain rings. The inner was designed to work with 26, 28, and 30 tooth chain rings. The exclusivity is a problem if you're trying to match the crank with any other shifting, but it's a benefit if you want XX. The benefit is that with less metal reaching from the chain ring teeth to the spider, there will be less flex, and faster response when pedaling. They also made the support area of the chain rings wider, out to 6mm, wider than other chain rings on the market. More meat means greater stiffness. And with 7075-T6 aluminum as the material, they're also pretty damn light. Not only did they design their own optimized bolt circle diameters, but they re-engineered the shift ramps, pins, and cut outs on the outer chain ring. On most chain rings these days, there are two sets of ramps and two drop points where the chain can get lifted or dropped quickly and under pressure. This means that twice each pedal revolution you'll hit these spots, so the shifting can be iffy if you shift at any other time. You've probably experienced this with the pause and clunk on some shifts and the smooth movement on others. SRAM's XX outer ring allows perfect shifts just about all the way around the crank. They call this X-Glide. Another improvement stems from having only two rings. From the small ring, the chain can only go up, from the big ring, only down This made designing the rings so they worked perfectly with each other easier than having to think about how the chain goes up from the small to middle ring and down from the big to middle ring. SRAM also worked the crank to make the Q-factor a lo
There have been no reviews posted yet for this product. Be the first by clicking Submit a Review
Can someone give me some advise. I'm looking to replace my jockey wheels on my SRAM XX deraileur. I'm just wondering can I replace with an X0 or X9 Jockey wheels instead..I'm guessing as long as it's 11 tooth it should be fine. Just rather not spend £120 on a set of official XX Jockey wheels.
Any a ... Read More »
So, I've adjusted the bike, buddy adjusted the bike, and the bike has stumped 3 mechanics at the shop so far (on two visits). So really, that's five people.
The story: The bike is a 29" titanium hardtail fitted with sram xx 2x10 (11-36). It probably has 400-500 miles on it. It shifts flawlessly ... Read More »
I have a first year XX Rear D that recently has the lower swingarm weak which now gives me all kinds of chain slap and the chain falls off alot now.
I've taken it apart and either that enclosed spring has gotten weak or the inside tab is coming out of it hole and popping into an lower tension hol ... Read More »
Currently my xx brakes make noise on my Remedy 9.9. I want to try to change out the rotor. What high end rotor do you recommend while considering weight and the fact I ride these on technical single track (I will use 180 front and back).
Thanks for any help.Read More »
[COLOR=#444444][FONT=sans-serif]Managed to find a good deal on a set of 2012 120mm dual air SID XX's but really, 100mm is the sweet spot for my frame - does anyone know if its possible to change the travel on these?
I know that you could add/remove spacers on the older Rockshox and am pretty sure th ... Read More »