SRAM Pressfit GXP Bottom Bracket

1/5 (1 Reviews)
MSRP : $40.00


  • Store Price
    Buy Now
    Buy Now
    Buy Now
    Buy Now
    Buy Now
    Buy Now
    Buy Now

Product Description

AllowsThe for installation of SRAM/Truvativ GXP cranksets on MTB frames/bikes usingThe PressFit standard. Stainless steel bearings Works with PressFit frames with 92mm wide unthreaded bb shell and 41mm inside diameter For use with GXP cranksets(SRAM orTruvativ) Ships withTruvativ packaging


Review Options:  Sorted by Latest Review | Sort by Best Rating

Reviews 1 - 1 (1 Reviews Total)

User Reviews

Overall Rating:2
Value Rating:2
Submitted by Norm Deplume a Cross Country Rider

Date Reviewed: October 19, 2014

Strengths:    Fits as it should without adapters.

Weaknesses:    Poor durability

Bottom Line:   
Replaced the Shimano bottom bracket that came with my frame with this SRAM BB for a better fit. The shop that built the bike had used paper thin plastic spacers to shim up the Shimano BB, which quickly melted away as I rode. This caused a wobble and eventually the bearings wore out. It is hard to say which BB performed better because of this installation issue. I was surprised that this GXP bracket's bearings wore out after less than a single season of riding. They now make a clicking noise. I removed the crank and, sure enough, the bearings feel rough when turned by hand. I am a 235 lb. rider, but I do not ride aggressively, and have not exposed this BB to mud, rain, or a lot of dust. I ride 20 miles a week on this bike at the most.

Expand full review >>

Price Paid:    $34.00

Purchased At:   ebay

Similar Products Used:   Shimano BB92, Shimano Hollowtech 2, Race Face X-type Team XC

Bike Setup:   2012 Trek Superfly AL Elite. 1X9 drivetrain with Truvativ Stylo 1.1 180mm crankset.

Overall Rating:1
Value Rating:1
Submitted by Tom Robinson a Weekend Warrior

Date Reviewed: July 15, 2013

Strengths:    None that I am aware of

Weaknesses:    Wore out in less than 6 months of use

Bottom Line:   
Supplied as original equipment on my 2012 Epic. I have never worn out a BB before in less than 4 years use in my life. The bearings felt stiff after 3 months use. I guess they had gone a bit rusty. They freed off with a backward and forward spin of the cranks. 3 months later there was detectable play, and they needed replacing! When I took the crank out, the left hand inner race was seized on to the shaft and had to be ground off. What a nightmare. I replaced the bearings from a bearing supplier and all working well now. I am unimpressed by BB30. I can only see that it saves money in production, and has no benefit to the owner.

Expand full review >>

Similar Products Used:   Hope BB excellent
Many different Shimano variants - good
Race Face - lasted 2 years then sheared the drive side splines


Bike Setup:   Specialized Epic Comp Carbon 2012

Reviews 1 - 1 (1 Reviews Total)

Review Options:  Sorted by Latest Review | Sort by Best Rating


Greasing SRAM Pressfit GXP bottom bracket bearings

My previous bike had BB30, and greasing the bearings on that was simple: Remove the crank, remove the outer seals, remove the bearing seals, add grease, reassemble. Just purchased a new used bike that has Pressfit GXP, and not sure how to do it here. The drive side bearing looks very similar, and t ... Read More »

SRAM GXP Pressfit BB coming loose?

Noticed this morning after a very rough race yesterday that my cranks were loose. So I tightened it up this morning and went for a smoother ride this afternoon and they are loose again. Is this a regularly problem? ThanksRead More »

Read More »



 

INTERBIKE

Contests





Interbike Featured Booths

Check out the hottest mountain bike products from these brands!



















See All Interbike Coverage - Click Here »

   

MTBR on Facebook