Review Options:
Sorted by Latest Review | Sort by Best Rating |
|
Reviews 1 - 9 (9 Reviews Total)
| |
User Reviews
Overall Rating:
Value Rating:
Submitted by
Piers Newland
a Cross Country Rider
from WakefieldDate Reviewed: July 3, 2004
Strengths: It's still on my bike after 9 years!Weaknesses: NoneBottom Line: I've just realised how long I've been using these bars - nearly 10 years! I'm either blissfully ignorant of some dire disaster awaiting me with these bars (there's no way I'd use light weight Al bars for more than a year or two and everything else wears out or bends) or I'm on to a winner. They are now on a fully rigid Pace and I use that hard offroad (check the pic on http://www.blacksheepmbr.co.uk/new_page_1.htm to see the trails they suffer).
Top product!
Duration Product Used: More than 3 years
Price Paid:
$90.00
Purchased At: Stif Leeds
Similar Products Used: Loads of Al flats and risers.
Bike Setup: Fully rigid Pace RC200 f8, XT & Hope
Overall Rating: Value Rating:
Submitted by
Evan
a
from IllinoisDate Reviewed: August 2, 2001
Bottom Line: These bars are manufactured by Koski Engineering for WTB; my review is under that name.
Duration Product Used: Less than 1 month
Price Paid:
$125.00
Purchased At: WTB
Overall Rating: Value Rating:
Submitted by
Evan
a
from IllinoisDate Reviewed: August 2, 2001
Bottom Line: These bars are manufactured by Koski Engineering for WTB; my review is under that name.
Duration Product Used: Less than 1 month
Price Paid:
$125.00
Purchased At: WTB
Overall Rating: Value Rating:
Submitted by
Piers Newland
a Weekend Warrior
from Wakefield, West Yorkshire, UKDate Reviewed: July 23, 2001
Strengths: It's still going after 7 years! Comfort of Ti (and the non-catastrophic mode of failure).Weaknesses: Still nowt.The £90 price is working out about £13/year.Bottom Line: The bars are still in use after 7 years (check the review somewhere below and I'm confident in them.
Why aren't they on one of my off-roaders? I finally gave in to the riser trend because their bend was more to my liking. The WTB bars are 7 degrees and the risers are about 12 degrees.
Would I buy them again? Yes, in a stronger bend, but don't tell my wife cause I still get my ears bent about the price once in a while.
Favorite Trail: Peak District technical
Duration Product Used: More than 3 years
Price Paid:
$90.00
Purchased At: Stif Mountain Bikes Leeds
Similar Products Used: Assorted Al flatties and a trio of riser bars.
Bike Setup: Raleigh M-Trax titanium and 531 steel bonded frame set up for commuting (including some off road).
Overall Rating: Value Rating:
Submitted by
Reverend R. Greyson
a Cross Country Rider
from late of ColoradoDate Reviewed: March 13, 2000
Strengths: COMFORTABLE. Ssstrong. Beautiful. Light. Made by little guys in US.Weaknesses: Spendy.Bottom Line: These bars are the answer for comfortable wrists. So comfortable with the 24" width and 16(yes indeed) degree bend! Super strong, super light, super comfortable. Don't need bar ends with this new improved angle. Put some on my hardtail, and the mtb tandem...even my wife shelled out for them, on her hardtail! If you hold yer arms out in front of you and look at yer hands, you'll see the natural angle in yer wrists...make them happy and get this bar at yer LBS.
Favorite Trail: wouldn't you like to know...
Duration Product Used: More than 3 years
Similar Products Used: Lots of different flat,road,riser bars.
Bike Setup: Ti custom hardtail with this fine bar, and a tandem with it too.
Overall Rating:
Submitted by
Bill Boles
a cross-country rider
from Brockton, MA USADate Reviewed: April 2, 1998
Bottom Line:
I had my WTB Ti handlebar custom bent to 13 degrees. I've used it 2 years now and love it. Everyone who rides my bike comments on how comfrtable the bars are. I tell them that it's the bend, but most remain unconvinced. Oh well. Their loss.
I rode my bike for 324 hours last year and did not experience the numb hands that I've occasionally experienced in the past with Aluminum, Titanium and steel bars that were bent at a more common 5-7 degrees.
If you decide to go with WTB bars I'd reccommend getting them bent to an ergonomically correct 12-13 degrees.
Ride on!
Overall Rating:
Submitted by
Piers Newland
a cross-country rider
from Wakefield, West Yorkshire, England.Date Reviewed: November 25, 1997
Bottom Line:
I wanted a tough, wide bar that would bend gracefully in a crash rather than snap suddenly (I may not be much to look at but I don't fancy drastic surgery by Doctor Rock). I got a 24 WTB Ti bar and it's been on my steel hardtail for 3 years now. It's still straight and I still have confidence in it's ability to hold me up no matter what I run into. The width is fine for tight, twisty, single track control and dead comfy everywhere. If you want wide bars that you can rely upon go for these. They're lighter and more fatigue resistant than cross-country riser bars and you won't need to change youe stem's rise or length. The only down side is the cost, £90 is alot for a shimmed piece of pipe and my wife still brings it up (good naturedly).
Overall Rating:
Submitted by
Nolwenn DERVIEUX
a weekend warrior
from Saint Malo FRANCEDate Reviewed: June 6, 1997
Bottom Line:
I bought a 22' length, 6° bent handlebar which seems to be three time lighter than the original one.Although I can feel all the vibrations generated by the off-road tyre at the asphalt, the usual pain in my wrist disappeared.But it is extremely expensive (735 FF), so I put four stars
Overall Rating:
Submitted by
Gary
a cross-country rider
from Southeast U.S.Date Reviewed: August 27, 1996
Bottom Line:
W.T.B., as I found out, will custom cut and bend a Ti bar for you. I had one cut for me -- 24, 9degree
bend. After having ridden 5 degree aluminum bars for 6 years, I can say that this custom bar was one
of the best purchases I have ever made. I've been riding it now for about two months. I feel more
comfortable and controlled in singletrack and at speed. Bunnyhopping is a piece of cake. It takes the
edge off the rough stuff (I'm riding rigid right now). And the pain in my wrists and forearms I was
having after every ride with the 5 degree Al bars is no more. I can't say enough about this great product.
It was a simple solution to a painful problem. Hey, ex-BMXers, remember your old bars had a ten degree
bend? The W.T.B. bars have a lifetime warranty to boot.
May your singletrack be curvy and your aim be straight.
|
Reviews 1 - 9 (9 Reviews Total)
| |
Review Options:
Sorted by Latest Review | Sort by Best Rating |
